Product range · market-entry batch 1

Unintended Car Movement & Ascending Car Overspeed Protection

Retrofit-ready detection and braking devices for lifts that pre-date modern safety requirements.

4 sub-ranges Documentation with every order OEM cross-reference available

Why independent contractors need these

Unintended car movement protection and ascending car overspeed protection were introduced into European requirements well after a large share of the installed base was commissioned. Retrofitting existing units is therefore one of the most frequent safety upgrades requested during periodic inspection — and one of the line items with the shortest replacement cycle, typically two to four years for the sensing and triggering elements.

What we supply

Detection devices, triggering units and the braking components that work with them, sourced from manufacturers whose products carry type-examination certification from an EU notified body. We supply the documentation set alongside the hardware so that the installer can assemble a complete technical file.

Selection is the hard part

UCMP/ACOP devices are not interchangeable. Correct selection depends on drive type (traction or hydraulic), rated speed, car mass, the existing controller's interface and the installation's original design standard. Send us those five data points and we will confirm a configuration in writing before you order.

Data we need to configure a UCMP/ACOP solution

  • Drive typeTraction (geared / gearless) or hydraulic
  • Rated speedm/s, as marked on the installation's rating plate
  • Car masskg, including rated load where available
  • ControllerMake, model and firmware generation if known
  • Existing protectionWhether any UCMP/ACOP device is already fitted
  • Reference standard of the installationEN 81-1/2, EN 81-20/50 or national code
Before you order

Send the data above with your enquiry. For safety components we will not quote without it, because selection errors invalidate the type examination and cannot be fixed on site.

What we supply

Sub-ranges

Car movement detection

Devices that sense car movement with the doors open and initiate the protective sequence.

Selection data: Drive type · rated speed · controller interface · supply voltage

Overspeed detection (ascending car)

Speed monitoring for upward overspeed, with triggering output to the braking element.

Selection data: Rated speed · triggering speed band · output type · encoder/switch input

Triggering and braking elements

Actuation components that apply the protective brake once a detection event is confirmed.

Selection data: Car mass · rail profile · rope configuration · mounting envelope

Interface and wiring kits

Adapters, harnesses and terminal hardware needed to connect a retrofit device to an existing controller.

Selection data: Controller make and model · voltage · signal polarity · DIN rail space

Product records

Individual product records for this range are being added

Each record will carry the OEM cross-reference numbers we have verified, the full specification, the reference standard, the type-examination certificate number and issuing notified body, the certificate validity term, lead time and minimum order quantity.

We are not publishing part numbers ahead of verifying their certification. If you need a component from this range now, send us the OEM number or the specification and we will reply with a written configuration.

Enquire about this range
Questions

Frequently asked

Do your UCMP devices carry EU type examination?

Safety components placed on the EU market require type examination by a notified body under Module B, with production conformity assured under Module C2 or D. We supply the EC type-examination certificate and the EU declaration of conformity for every safety component we list. Certificate numbers are quoted on the individual product record — we do not publish them on this overview page because they are tied to specific configurations.

Can you match a device to my existing controller?

Yes. Send the controller make and model, the drive type, rated speed, car mass and a photo of the existing wiring. We will reply with a written configuration and the interface parts required. This is the fastest route to a correct quotation.

Do you supply complete retrofit kits?

We can quote a kit (detection + triggering + braking + wiring) or individual elements where the installer is only replacing a failed component. Tell us which case applies.

What about ISO 8100-1:2026 / ISO 8100-2:2026?

These standards were published on 27 March 2026 and succeed EN 81-20:2020 and EN 81-50:2020. Where a manufacturer has updated its type examination to the new standards we will say so on the product record and provide the current certificate. Where a device is certified against EN 81-20:2014/2020 it remains valid for its certificate term — we state the reference standard explicitly so you can judge it against your own national requirements.

Need this range configured for a specific installation?

Send the OEM part number or the specification, the installation details and your required date. You will get a written configuration — or an honest no if we cannot supply a certified equivalent.

Request a quote