Quality & compliance

Certification and compliance

Safety components are not ordinary spare parts. This page states what we supply, what documentation travels with it, and where the responsibility sits between us and you. If any of it is unclear for your market, ask before you order.

Safety components and type examination

Under EU law, certain lift components are classified as safety components. Placing one on the EU market requires assessment by a notified body: an EU type-examination certificate issued under Module B, together with assurance of production conformity under Module C2, D or equivalent, depending on the route the manufacturer has taken.

We supply the certificate and the EU declaration of conformity for every safety component we list. We also state the validity term, because these certificates are issued for a defined period and are subject to surveillance — a certificate that was current at manufacture may not be current at installation, and you are entitled to know which you have.

Standards: the EN 81 to ISO 8100 transition

EN 81-20:2014 and EN 81-50:2014, as amended and consolidated in the 2020 editions, have been the reference standards for lift safety and for the design and testing of safety components.

ISO 8100-1:2026 and ISO 8100-2:2026 were published on 27 March 2026 and are the successor documents to EN 81-20 and EN 81-50 respectively. The European Lift Association has published a comparison of the two sets. However, publication of a standard and its listing as a harmonised standard in the Official Journal are two different things: the European Commission is still preparing the implementing decision listing harmonised standards under the new Machinery Regulation.

In practice, for a component you are buying today: a device certified against EN 81-20:2014 or the 2020 consolidated edition remains valid for the term of its certificate. Where a manufacturer has re-issued its type examination against the ISO 8100 series, we say so on the product record. We always state the reference standard explicitly rather than writing 'CE approved', so you can judge it against your own national requirements.

Lifts Directive and the Machinery Regulation

Lifts and safety components are currently governed by Directive 2014/33/EU. Regulation (EU) 2023/1230 — the new Machinery Regulation — becomes applicable on 20 January 2027 and will supersede the Directive for products placed on the market from that date. The European Commission has published a technical guideline on the transition.

For our customers the practical question is which regime applies to the component at the time it is placed on the market, and whether the certificate in hand was issued under the outgoing Directive. We quote the certificate's issuing notified body, its number and its reference so you can establish this for yourself. Where a manufacturer has already transitioned its certification, we will tell you.

What we are not

We are not a notified body and we do not issue certificates. We are not the manufacturer of the components we supply, and we do not perform the conformity assessment.

We are also not your installer. Responsibility for correct selection against the specific installation, for the installation itself, and for the technical file of that installation rests with the installer and, where applicable, with the person placing the installation into service. Our responsibility is to supply the component specified, with accurate documentation, and to tell you clearly when a configuration is outside what the certification covers.

If a selection decision has safety consequences and our written confirmation is not sufficient for your purposes, involve your own competent person or your national inspection body. We would rather delay an order than have you rely on us for something outside our role.

Documentation supplied with each order

Documents supplied
DocumentApplies toDetail
EU declaration of conformityEvery safety componentFor the specific configuration supplied
EC type-examination certificateEvery safety componentCertificate number, notified body, validity term
Reference standardEvery safety componentEN 81-20/50 edition, or ISO 8100 series where applicable
Installation & maintenance instructionsAll productsLanguage confirmed at enquiry stage
Packing list & commercial invoiceEvery shipmentWith HS 8431.31 classification stated
Certificate of originOn requestSpecify the form required at enquiry stage
Test / inspection recordsWhere applicableComponent-type dependent

Commodity coding and customs

Elevator and lift parts are classified under heading 8431.31 in the Harmonised System. We declare this heading on export documentation and expect it to be used on import.

We flag this specifically because misclassification into a neighbouring heading for other lifting machinery can bring a component into the scope of anti-dumping measures that do not apply to lift parts. Correct classification is in both our interests.

Duty treatment in the EU, origin rules and any applicable anti-circumvention requirements are matters for your customs agent or broker. We supply accurate product descriptions, HS coding and origin information; we do not give customs or legal advice, and you should not treat anything on this site as such.

Our role, stated plainly

We are a trading company. We are not a notified body, not a manufacturer and not your installer. Our responsibility is to supply the component specified with accurate documentation, and to say clearly when a configuration falls outside what that certification covers.

Standards are moving

ISO 8100-1:2026 and ISO 8100-2:2026 were published on 27 March 2026 as successors to EN 81-20 and EN 81-50. Regulation (EU) 2023/1230 becomes applicable on 20 January 2027. Where it matters for a component you are buying, we state the reference standard and certificate term explicitly rather than writing "CE approved".

Need certification details before you commit?

Send the component you are specifying and we will provide the certificate reference, the issuing notified body, the reference standard and the validity term in writing — before you place an order.

Request documentation